Technical Centre

How to choose a tile cutter, and why cuts fail

The technical questions distributors actually get asked — which length for which tile, why a cut chips, which spares to hold, and how a mixed container fits together. Written for the person who has to answer the customer, not for a spec sheet.

0.6–1.8 m
Cutting length coverage
3–18 mm
Cutting depth range
1
Scoring wheel for the whole range
Guide 01

Match the cutting length to the tile

The common mistake is buying a cutter the same length as the tile. For a straight cut along the short side that works. For a diagonal cut it does not, because the cut runs corner to corner — the diagonal, not the side.

Tile formatDiagonalStraight cut needsDiagonal cut needs
300 × 300 mm424 mmTC-S600TC-S600
300 × 600 mm671 mmTC-S600TC-S800
600 × 600 mm849 mmTC-S800TC-S1000
600 × 1200 mm1342 mmTC-S1200TC-X1600 / TC-A1600
800 × 1600 mm1789 mmTC-X1600TC-W1800 / TC-A1800
800 × 1800 mm1970 mmTC-W1800Beyond the range — ask us

Diagonal = √(width² + height²). Allow a margin: the tile has to sit inside the bed at both ends of the score, not just fit the length.

Rule of thumb for stocking: if your market sells 600 × 1200 mm porcelain and does any diagonal work, the 1.2 m machine is under-specified and you will get returns. Stock 1.6 m alongside it.

Guide 02

Why a cut chips

Four causes, in the order we see them. Three are the machine; one is the operator — and it is the one customers blame the machine for.

Cause 01

Worn wheel

A scoring wheel that has lost its edge tears the glaze instead of scoring it. The crack that follows wanders off the line. Replacing the wheel is the cheapest fix in the list.

Cause 02

Rail flex

If the rail bows under pressure mid-score, the score depth varies along the cut and the tile breaks unevenly. This is the difference between a solid rail and a folded one.

Cause 03

Bed not true

Debris under the tile, or a base that has been dropped, lifts one corner. The tile flexes while being snapped, and the break follows the flex.

Cause 04

Pressure

Too much pressure crushes the glaze; too little gives no score at all. One firm pass, not several light ones, and never a second pass over the same line.

Guide 03

Which spares to hold

Because the whole range shares one wheel and one spares kit, a distributor's service stock is unusually simple: one part number covers every model on the shelf, from the 0.6 m entry machine to the 1.8 m wide-base model.

Every carton already ships with an oil can, a tool set, screws and nuts, and two spare wheels — so the end customer is not waiting on a part in the first weeks of ownership. What sits on your shelf is the replacement stock for year two onward.

Rule of thumb for a first container: a small percentage of unit count in spare wheels, and a handful of tool sets. We will suggest a number against your actual mix.

Scoring wheelShared across every model in the range
In every carton2 spare wheels, oil can, tool set, screws and nuts
Wear partsWheel, oil — not covered by warranty
Order with shipmentYes, at no extra freight
Order separatelyYes, for restocking
Spare parts listRequest it
Guide 04

Planning a mixed container

A mixed order is normal, but long cartons make the arithmetic less obvious than it looks. Three practical points:

Length dominates. The 1.6 m and 1.8 m machines ship in cartons of 1,865 mm and 2,065 mm (170 × 250 mm section), and the TC-X and TC-A long lengths in 2,040 mm and 2,240 mm cartons. They have to be loaded lengthwise and cannot be stacked arbitrarily, so they take more of the container than their cubic volume suggests.

Weight concentrates. TC-W is 24.6–26.86 kg net per unit. A stack of wide-base machines in one corner is a load-distribution question, not just a space question.

Packaging changes the count. Own-brand cartons from 200 units are usually a different size to the standard export carton, so the loading plan has to be rebuilt when packaging is customised.

Send us the mix and we return carton dimensions and gross weights per model, so your forwarder can do the loading calculation on real numbers rather than estimates.

Guide 05

Documents we send

  • Specification sheet per model — sizes, weights, carton dimensions
  • Packing list with carton dimensions and gross weights
  • Proforma invoice and commercial invoice
  • Certificate of origin
  • Bill of lading — original or telex release
  • Pre-shipment photographs of the packed order
  • Spare parts list for your service stock
  • Certification arranged to your destination's requirements
Download the sheets
Downloads

Specification sheets, straight from the source

One page per machine: SKU table with net and gross weights and carton dimensions, carton contents, and the buying terms. No form required.

A technical question we have not answered?

Send it to the export team. If it is a good one, it usually ends up on this page.

Request a Quotation
WhatsAppGet Pricing